Inventory

For sale
Okuma LS 540 Metal Lathe.

Lathe has been disassembled cleaned and painted.
All gear boxes have been drained flushed and filled with correct oil.
All new Original rubber way wipers
New wipers for Feed screws
Many new parts from Original Okuma “Rebuild Kit”

Geared Head Engine Lathe
Hardened Bed
Inch/ mm Thread
10″ Three-Jaw Chuck
(Choice of) 4 jaw chuck
4 position tool post. (Aloris model CA tool post and tool holders Available)
Carriage Stops 2 included 1 on each side of carriage
Z axis automatic feed stop.
Center for Hydraulic tracer attachment
Extra change gear for Metric threading
Coolant System

Capacities:
Swing Over Bed: 21″
Swing Over Cross Slide: 10.6″
Swing Over Compound Slide: 5.5″
Distance Between Centers: 62″

Spindle:
Mount: D1-6
Thru Hole: 2 1/4″
Number of Speeds: 12
Speed Range: 35 to 1,800 RPM

Carriage:
Cross Slide Travel: 10.6″
Compount Slide Travel: 5.5″
T-Slot Dimnesions: 1-3/16″ x 1-55/64″ (approx.)

Threads:
Inch: 4 to 56, Metric: 0.5 to 7mm

Tailstock:
Spindle Taper: #4 Morse Taper
Spindle Diameter: 2.56″
Spindle Travel: 6-3/4″

Bed:
Width: 16″
Length: 76″

General:
Motor: 10 Horsepower, 220/440 Volt, 1,500 / 1,800 RPM, 50 / 60 Hz
Current Electrical: 220 Volt, Three Phase
Overall Dimensions: 110″ x 48″ x 60″ tall, Weighs: 7000 Lbs

Nardini MS1440E Gap Bed lathe.

Lathe is in very good condition.
Lathe has been disassembled,cleaned, and adjusted.
All oils have been drained and flushed and filled with correct oil.
Cross slide screw has .004 backlash and operates smoothly.

Lathe features
Automatic feed disconnect on X and Z axis.
Swing Over Bed: 14″
Swing Over Cross Slide: 7-7/8″
Swing In Gap: 19-3/4″
Distance Between Centers: 40″”
Cross Slide Travel: 8″
Top Slide Travel: 4″
Spindle Speeds: (18) 31.5 to 2500 RPM
Tailstock Quill Diameter: 2″
Tailstock Taper: No. 3 MT
Tailstock Quill Travel: 5-1/8″
Number of Threads: 192
Metric Threads: (45) .40 to 7
Inch Threads: (48) 3.5-42 TPI
Module Threads: (48) .1 to 1.75
Diametral Pitch Threads: (48) 14 to 168
Pitch Of Leadscrew: 4 TPI
Number of Feeds: 192
Longitudinal Feeds, Inch: .0016 to .399 in/rev
Longitudinal Feeds, Metric: .042 to 1.013 mm/rev
Cross Feeds, Inch: .0007 to .0213 in/rev
Cross Feeds, Metric: .019 to .542 mm/rev
Equipped With:
8″ 3 jaw. (Runout checked at .0015″)
10 ” 4 jaw.
Drill chuck
Quick change tool post.
Micrometer stop
Coolant pump system
OSHA approved spindle Guard.

For Sale

Clausing Colchester 17″ x 80″ Lathe in Mint condition with Tooling

Included with Lathe is

3 and 4 jaw Pratt Burrnard Chucks

Large Faceplate

Dog Driver

Steady rest ,brass and roller inserts. (Brand New 1st time out of box was to take pictures )

Micrometer Carriage  Stop

Drill chuck

Coolant Tank and Pump.

This lathe has just been serviced including

Cross slide disassembled clean and Gibbs adjusted

All oil gallies cleaned , flushed, and verified oiling

Head Stock oil and quick change gear box oil changed.

Cross Slide is in Like New condition (See pictures when taken apart for service “

Lathe is powered and can be tested

1. Will load on truck or trailer at no charge

For Sale

Southwestern Industries Proto Trak 1630SX Lathe

Lathe is in Like New condition and still has Original Paint.

Machine has just been serviced including

Headstock oil has been drained , flushed and filled with New Oil

Saddle and Cross Slide have been disassembled , cleaned , flushed and verified all oil gallies are oiling correctly.

Lathe has been Calibrated using Fixture from Proto Trak

Latest Software

Comes with

8″ 3 Jaw Chuck

8 position Dorian Smart Dex programmable tool changer

Lathe is powered and can be Tested

Can load on truck or trailer at NO Charge

For Sale (Grafton Ohio)

19″ X 54″
LEBLOND ENGINE LATHE
(This lathe DOES come with a full,back splash chip gaurd not shown in pictures)

SERIAL ……………………… 8F-2484
MODEL ………………………. REGAL
SWING OVER BED ………………. 19″
SWING OVER CROSS SLIDE ……….. 12-1/4″
DISTANCE BETWEEN CENTERS ……… 54″
HOLE THRU SPINDLE ……………. 1-3/4″
SPINDLE SPEEDS ………………. 25 TO 1000 RPM
FEEDS ………………………. (66) .0018 TO .104 IPR
THREADS …………………….. (66) 2 TO 112 TPI

CHUCK ……………………….
8″ 3 JAW CHUCK

TAPER ATTACHMENT …………….. YES

HARDENED REPLACEABLE WAYS …….. YES

TREAD DIAL ………………….. YES

SPINDLE MOTOR ………………..
10 HORSEPOWER
Machine has just been serviced.

Compound , Cross slid and Carriage have been removed cleaned, flushed and verified oiling gallies are clean and oiling as the should.

TAPER ATTACHMENT HAS BEEN DISASSEMBLED CLEAN LUBED AND ADJUSTED.

*May inspect under power.

Will load on truck or trailer at no charge

For Sale ( Huger South Carolina)
Clausing Colchester Lathe 15″x 50″VERY GOOD Condition!
NEW IN 1988
Lathe has just been serviced , including
Headstock ,Quick Change Feedbox and Carriage have been drain , flushed and filled with New Oil
Cross Slide has been disassembled cleaned and verified oiling properly.( see pictures cross slide still has original machine marks Like NEW) Backlash on all feed screws are .005″ or less
New Drive belts
New wipers for Ways on carrige and Tailstock

Demo Video

Lathe is powered and can be tested
Will load on truck or trailer at no charge.

EQUIPPED WITH

INCH/METRIC THREADING
10″ 3-JAW CHUCK
TAPER ATTACHMENT
TAILSTOCK with 4 MT
COOLANT SYSTEM
Factory Work Light
THREAD CHASING DIAL
STEADY REST
ELECTRIC SPINDLE BRAKE

Description
SPECIFICATIONS

CAPACITIES
SWING OVER BED: 15-1/4″
SWING OVER SADDLE WAYS: 15-1/4″
SWING OVER CROSS SLIDE: 9-1/2″
BAR CAPACITY THRU SPINDLE: 2-1/8″
DISTANCE BETWEEN CENTERS: 50″

HEADSTOCK
SPINDLE NOSE: 6″ D-1 CAMLOCK
HOLE THRU SPINDLE: 2-3/16″
SPINDLE CENTER: 4 MT
SPINDLE BEARINGS: GAMET PRECISION
SPEEDS (16): 25 -2000 RPM

THREADS & FEEDS
US STANDARD THREADS (45): 2 – 72 TPI

METRIC THREADS (39): .2 – 14 MM
LONGITUDINAL FEEDS (45): .0015″ – .040″
CROSS FEEDS: .00075″ – .020″

CARRIAGE
LEADSCREW DIAMETER: 1-1/4 – 4 ACME
FEED ROD DIAMETER: 7/8″
LENGTH ON BED: 17″
WIDTH OF BRIDGE: 7-3/4″
CROSS SLIDE: 21-1/4″ X 6″ WIDE
CROSS SLIDE TRAVEL: 9-1/4″
CROSS FEED DIAL (E/M STD.): DIRECT READING
COMPOUND REST TRAVEL: 4-3/4″
TOOL BLOCK, CAPACITY: 2″
CROSS, COMPOUND SLIDE GIBS: TAPERED

TAILSTOCK
SPINDLE DIAMETER: 2-5/16″
CENTER: 4 MT
SPINDLE TRAVEL: 6-1/8″
SPINDLE GRADUATIONS: 0-5″ BY 1/16″

BED
WIDTH: 11″
DEPTH AT CENTER: 10-1/2″
WAYS, INDUCTION HARDENED: 2V, 2 FLAT

GENERAL
DIMENSIONS: 96″ LR X 38″ FB X 49″ H

For Sale  (Grafton Ohio)

Southwestern Industries

Proto Trak B3 Sport ( like DPM3) Vertical Bed Mill

with SM3 CNC Controls

The following Service has just been Completed

All new bearings in variable speed head Including New variable speed belt.

Table removed and cleaned.

All oil gallies have been cleaned, flushed, and verified oiling correctly.

Ball screwed cleaned and flushed with new oil.

New rubber lines replaced to ball screws

This is a very nice Mill that runs smooth and quite.

Video of machine operation can be shared upon request.

Table size 50″ X 10 ” ~ with 3 t-slots

Travel X-29 / Y-16″ / Z-24.150″

Maximum weight of work piece: 1,320 LBS

Milling head swivels right & left: 90 Degrees

Quill travel: 5″

Spindle taper: #40 N.S.T

(3) power quill feeds: .002; .004; .006 IPR

Distance, center-line of spindle to face of column: 17.3″

Variable spindle speeds 70-4200 RPM

Full 3-axis CNC machining control or hand wheels for manual operation

Precision and ground ball screws installed in table(X), saddle(Y), and column(Z)

3 H.P. spindle drive motor

Approximate Weight: 4,200 Lbs.

Approximate Dimensions: 71″ x 71″ x 84″ H

Equipped With:

Dual floppy disc drives

RS 232 port

Automatic lubrication system

(cleaned,flushed, and filled with new oil)

Torque Rite power drawbar.

For Sale (Grafton Ohio)

2008 Haas TL-1 CNC Lathe

Lathe has just been serviced all grease flushed and clean.

2000 rpm spindle

Tailstock with #4 Morris Taper.

1590 Hours Powered up. 13 hours cycle time 10 hours cutting time. Lathe is powered and can be tested

For Sale (Grafton Ohio)
Sentec (same as Sharp) Bed mill with Southwestern Industries Proto Trak CNC Control

2 axis Conversational CNC control that also can be used manually with DRO
Mill has just been serviced including
New spindle belt and variable speed bearings . Runs very quite
Table and saddle have been removed, cleaned,flushed and inspected to verify oiling correctly
Gibbs adjusted
Proto Trak control has been calibrated to repeat Directional and Bi Directional within .0002.
Travel sensors have been cleaned and new wippers installed.

Mill has Power feed to raise and lower
Mill will include selection of collets, tool holders and 6″ Kurt Vise

Here is a Demo video of Mill

For Sale
LeBlond 15” x 54” Makino Regal Lathe, 2 17/64” Spindle Bore

Youtube Demo Video ( copy and paste to view) https://youtu.be/Cc7f_7G2exQ

Serial # 14C-536

Lathe has just been serviced , including.
Oil drained , flushed and filled with new oil.
Cross slide and Carriage disassembled clean , verified all gallies are oiling. Gibbs adjusted.
New High speed timing belt from Leblonde (steel belted)
Crossfeed and compound screws have .006-.008″ backlash

Specifications:
8″ 3Jaw chuck made in Sweden.
4 Jaw Cushman Chuck
Swing over Bed and Carriage Ways 15 ½”
Swing over Cross Slide 9 ½”
Distance between Centers 54”
Spindle Speeds (12) 45-1800 RPM
Spindle Bore Size 2 17/64”
Spindle Taper L-1
Headstock Length on Bed 15 7/8”
Bed width 12 3/16”
Carriage Length on Bed 19 7/8”
Cross Slide Travel 8 7/8”
Compound Rest Travel 3 7/8”
Feeds (48) 0.0018 – 0.104 IPR
Threads (48) 2-112 TPI
Leadscrew Diameter 1 3/16”
Tailstock Spindle Diameter 1 15/16”
Tailstock Taper M 4
Tailstock Length on Bed 10 ¾”
Motor 7.5 HP/ 45- 1800 RPM Servo shift
Dimensions 78” x 40”
Weight 3800 lbs.

Lathe is equipped with Sae and Metric Threading
Anilam Dro Z axis only.
Currently wired 208-240 volt 3 phase.

Lathe is powered and can be tested.
Will load on truck or trailer at no charge.

Leblond Makino 15×54 Lathe D1-6 Spindle –

YouTube Demo Video( copy and paste to view) https://youtu.be/52kRDlXgAeo

Lathe has just been serviced , including.
Oil drained , flushed and filled with new oil.
Cross slide and Carriage disassembled clean , verified all gallies are oiling. Gibbs adjusted.
New High speed timing belt from Leblonde (steel belted)
Crossfeed and compound screws have .006-.008″ backlash

Specifications:
10″ 3 Jaw chuck made in Sweden.
Swing over Bed and Carriage Ways 15 ½”
Swing over Cross Slide 9 ½”
Distance between Centers 54”
Spindle Speeds (12) 45-1800 RPM
Spindle Bore Size 2 17/64”
Spindle Taper D-16 camlock
Headstock Length on Bed 15 7/8”
Bed width 12 3/16”
Carriage Length on Bed 19 7/8”
Cross Slide Travel 8 7/8”
Compound Rest Travel 3 7/8”
Feeds (48) 0.0018 – 0.104 IPR
Threads (48) 2-112 TPI
Leadscrew Diameter 1 3/16”
Tailstock Spindle Diameter 1 15/16”
Tailstock Taper M 4
Tailstock Length on Bed 10 ¾”
Motor 7.5 HP/ 45- 1800 RPM Servo shift
Dimensions 78” x 40”
Weight 3800 lbs.

Lathe is equipped with Sae and Metric Threading
Currently wired 208-240 volt 3 phase.

Lathe is powered and can be tested.
Will load on truck or trailer at no charge.

For Sale
ATrump 3 axis CNC Milling Machine with Brand New Southwestern Industries KMX 3 Axis Control ( upgraded 5-7-20 1 Year warranty from time of Installation)

Mill Features
Spindle is Driven by Single Phase 220 volt Variable Speed Frequency Drive ( can also be wired 3 phase if needed)
58″ x 11″ Table in great condition
30 Taper Quick Change Spindle
Machine has just been serviced Including
All bearings in variable speed part of head have been replaced with New
Table and saddle have been removed ,oil gallies have been cleaned , flushed , and verified oiling properly
Ball Screws have been removed , cleaned and flushed with oil
New oil lines have been installed on ball screws
Mill has been calibrated with Southwestern Calibration Fixture
Mill will include your choice (10 Quantity) 30 Taper tool holder
Any Question please contact Brandon
Machine is powered and can be tested.
Will load on truck or trailer at no charge.

For Sale Southwestern Industries Proto Trak 1630SX Lathe with Programmable Tool Changer

For Sale
Southwestern Industries Proto Trak DPM 5 Bed Mill with A.G.E. CNC Control

This is a nice machine with Original Paint
The following Service has just been Completed

All new bearings in variable speed head Including New variable speed belt.
Table removed and cleaned.
All oil gallies have been cleaned, flushed, and verified oiling correctly.
Ball screwed cleaned and flushed with new oil.
New rubber lines replaced to ball screws
Mill has been adjusted and calibrated using Southwestern Industries Calibration Fixture, and is ready for Production
Kurt Power Draw Bar

Way covers have been removed for pictures. They will be included with machine.

This is a very nice Mill that runs smooth and quite.

Demo video of operation

Specifications:
Table size – 50″ x 12″
T-slots (number x width x pitch) – 3 x 16mm x 63.5mm
Travel (X, Y, Z axis) – 40″ x 20″ x 24″
Quill diameter – 4.13″
Spindle taper – NMTB 40
Spindle speed range RPM – 160-4000
Spindle center to column face – 20.5″
Spindle motor power – 5 HP
Power requirement, control – 110V, 1P, 15A
Power requirement, machine – 220V, 3P, 60HZ Current,
Full Load Amps – 17.5 FLA
Maximum weight of workpiece – 1760 lbs.
Height of table from bottom of bed – 41″
Maximum spindle nose to table – 24″
Minimum height – 87″ Maximum height – 100″
Width of machine including table – 94″
Length with electric box door closed – 80″
Overall width including full table travel – 136″
Overall length with electrical door open – 105″
Footprint – 24″ x 48.4″
Way surface – dovetail X axis; square ways Y and Z axis
Weight (approximate) net – 4400 lbs.
Weight (approximate) shipping – 4700 lbs.
Drill max capacity – 1″ dia.
Tapping max capacity – 5/8″
Milling max capacity – 5 inch @3″/min

Mill can be loaded on truck or trailer at NO charge

Any Questions please call Brandon

For Sale
Southwestern Industries Proto Trak 1630SX Lathe
Lathe is in Like New condition and still has Original Paint.

Demo video of operation

Machine has just been serviced including

Headstock oil has been drained , flushed and filled with New Oil

Saddle and Cross Slide have been disassembled , cleaned , flushed and verified all oil gallies are oiling correctly.

Lathe has been Calibrated using Fixture from Proto Trak

Latest Software and Compact Flash drive has been installed

Comes with
8″ 3 Jaw Chuck with Adjustable Scroll ( Tru Adjust)

CXA style Quick Change Tool Post

Also available at extra cost is a 4 Star 4 position programmable tool changer

Lathe is powered and can be Tested
Any question Please Call Brandon

Can load on truck or trailer at NO Charge

Take a look at
Varneymachine.com
For other Machinery needs.

Machine Specifications
· Height of Centers-8”

· Distance between centers-30”

· Swing over bed -16”

· Swing over saddle wings-16”

· Swing over cross slide-8.6”

· Cross slide travel-9.6”

· Tool section max-3 /4”

· Coolant tank capacity-11 gal.

· Width of Bed-12.6”

· Height of Bed-12.6”

· Spindle Nose (Camlock)-D1-6

· Spindle through hole-2.12”

· Spindle taper-MT#6

· Taper in reduction sleeve -N/A

· Spindle dia at front bearing-3.15”

· Number of bearings-2

· Bearing class (radial round)-P5

· Spindle speed range (RPM)-150-2500

· Optional Tailstock Quill travel-5”

– Quill diameter-2.36”

– Quill taper hole-MT#4

· Spindle Motor HP -7.5

· Power requirements, control-110V; 1P; 8 A

· Power requirements, machine-220V;3P;60Hz

· Amps full load current-25

· Dimensions net – 79 x 38 x 54”

· Dimensions shipping – 87 x 45 x 67”

· Weight net – 3,200 lbs.

· Maximum rapid feed X – 100

· Maximum rapid feed Z – 150

· Spindle motor brake – Dynamic braking

· Way surface hardness – 400 – 450 HB

· Head stock lubrication – Oil bath

· Sliding door for easy set-ups

· Bedways hardened and ground

· Sliding surfaces Turcite coated

· Dovetails on cross slide, V-ways on saddle

· Adjustable saddle gibs

ProtoTRAK SLX System Specifications
(O) indicates optional feature

ProtoTRAK System Hardware
· ProtoTRAK SLX CNC

· Two-axis CNC, two-axis DRO

· Electronic handwheels for manual operation

· 10.4” color active-matrix screen

· Industrial-grade Celeron® processor

· 128 Mb Ram

· P/S 2 Keyboard connector

· 2 USB connectors

· Override of program feedrate

· Override of program spindle speed

· LED status lights built into display

· TEAC floppy drive

· Gasket-sealed enclosures

· Jogstick for convenient jog

· Clean front panel with few hard keys

Software Features – General Operation
· Clear, uncluttered screen display

· Prompted data inputs

· English language – no codes

· Soft keys – change within context

· Windows® operating system

· Color graphics with adjustable views

· Inch/mm selectable

· Convenient modes of operation (see below)

DRO Mode features
· Incremental and absolute dimensions

· Jog at rapid with override

· Powerfeed X or Z

· Tapers of any angle

· Radius

· Fillet

· Go To dimensions (O)

· Servo motor return to Home

· Spindle speed setting with override

· Tool offsets from library

· Fine/course handwheel resolution for traking option (O)

Program Mode features
· Geometry-based programming

· Event comments (O)

· Incremental and absolute dimensions

· Automatic tool nose radius compensation

· Circular interpolation

· Linear interpolation

· Look –graphics with a single button push

· List step – graphics with programmed events displayed

· Alphanumeric program names

· Conrad – one input for automatic corner radius programming

· Chamfer – one input for automatic chamfer programming

· Math helps with graphical interface

· Auto load of math solutions

· Subroutine repeat of programmed events

· Nesting

· Programmable spindle speeds

· Program run time clock in Run Mode (O)

· CSS (Constant Surface Speed) programming (O)

· IPR (Inch per Revolution) programming (O)

· Gang tooling (O)

Canned cycles
· Position

· Drill

· Bore

· Turn

· Arc

· Cycle

· Thread

· Groove

· Custom thread (O)

· Tap (O)

Edit mode Features
· Delete events

· Erase program

· Spreadsheet editing (O)

· Global data change (O)

· Clipboard to copy events between programs (O)

Set Up Mode Features
· Program diagnostics

· Advanced tool library

· Tool library file save

· Icon-prompted tool setting

· Tool offsets with modifiers

· Single tool set-up

· Indexer tool set-up (O)

· Advanced diagnostic routines

· Software travel limits

· Tool path graphics with adjustable views

· Program run time estimation clock

Run Mode Features
· CAM file program run

· Real time run graphics with tool icon

· Countdown clock to next pause or tool change (O)

· TRAKing of programs during program run (O)

· Automatic indexing for tool change (O)

· Gang tool operation (O)

Program In/Out Mode Features
· Simple program storage to floppy

· CAM program converter

· Converter for prior-generation ProtoTRAK programs

· Selection of file storage locations (O)

· Automatic file back-up routine (O)

· Preview graphics for unopened files (O)

MAKE Webb ALL Original
MODEL WL- 435 ( serial number 9-8012-17)
SWING 17″ (26″ with gap removed)
CENTERS 40 Inch
MOTOR 5HP 220—440 VOLTS 3 PHASE
SPINDLE A 1-6 spindle with
2.100 spindle bore
10″ 3 jaw chuck with reversible jaws
4 jaw 12″ chuck
18″ face plate
14″ face plate
9.5″ and 12″ Dog driving plate
Trav a dial Model 7A
Steady Rest
Choice of Quick change tool post or 4 tool turret tool post
Live Center
Micrometer Carriage Stop

SPEEDS (12) 32—-1800
THREADS Inch / metric
Cross slide and lead screw are in Good condition.
Cross slide, compound, saddle, and oiling system disassembled, cleaned and adjusted.
Headstock drained, flushed and filled with New oil.

TAIL STOCK # 4 MORSE TAPER

This is a licensed copy of Mori-Seiki. All parts are interchangeable and available.

Very nice running lathe can be inspected under power

Any questions please call Brandon at Varney Machine
Local pickup
Can load on truck or trailer at no charge.

For Sale

Unison CNC Flexible Grinding System
Model 2200
3 Axis CNC Control with Multiple Uses

Plunge Grinding
In Feed Grinding
Surface Grinding
Multi Step Grinding
Profile Grinding
Internal Grinding
I.D. Profile Grinding
Mixed Mode Grinding ( Example )Combine Punge with a Profile Grind
Wheel Dress Cycle
Wheel Profile Dress Cycle

Ded Tru Centerless Grinding Fixture with Tooling

I.D. Grinding Attachment
Precise Liquid cooled High Frequency Grinding Spindle
Model SC77 10,000- 40,000 RPM with Controller

Precise Water Pump Chiller and Regulators
on Cart

Coolant Tank
Thermostat Controlled Tank Heater
Sediment Filter above Coolant Tank

3HP Pope Grinding Spindle

Air Conditioned Computer Control Cabinet

3 Green Containers of Wheel Adapters and Balance Rings(see pics)

Manuals
Programming Manuals

All Oil Lines have been Replaced and Verified Oiling

All belts were Adjusted and Inspected

Computer was sent to Unison To have CMOS Battery Changed, Latest Updates, and Inspected

Grinder is Powered and Can Be Inspected

More Pictures are available Upon Request

Will load on Truck or Trailer at NO Charge

Shipping can be Arranged BEFORE making purchase

Please Contact Brandon

for any questions about Grinder or Shipping

Other
DedTru Centerless Grinding Fixtures
I.D. Grinding Spindle (different RPM Ranges)
Watercooled Spindle Chiller Units
are
Available at Extra Fee

For Sale

2002 Southwestern Industries Proto Trak K3
with Edge 2 axis cnc control, 3 axis digital readout
10″ x 50″ Table
Box Ways in good condition
MNTB 30 taper Quick Change Spindle with Tooling (see pictures)
3 hp spindle drive motor
Power feed on knee (Z axis)
Adjustable Chip Deflector Guard

Mill has just been disassembled , cleaned , reassembled , adjusted and calibrated
All bearings in variable speed side of head have replaced and new drive belt installed
X axis servo motor is New

Mill is powered and can be tested .

Will load on truck or trailer at NO charge.

Any questions please Call Brandon

For Sale (Bridgeport Style)

Millport Vertical Mill 10″x50″ Table
Heavy Duty Box Ways
with AGE2 Prototrak 2 axis cnc control.
3hp spindle.
R-8 collet spindle with Kurt Power Draw Bar
Wesco dual nozzle” Tool Mist”
Mill has just been inspected and Serviced
Including
New variable speed belt ,bearings and head inspected
Table removed and cleaned.
Verified oiling system is working correctly.
Reassembled and Gibbs adjusted.
Mill has been calibrated using Proto Trak fixture

Here is a video of mill showing
Spindle (High and Low) and CNC control ,servo motors running

www.youtube.com/watch?v=Ulz9HUuzBN8

Mill is powered and can be tested.
Any questions please call Brandon

Can load on truck or trailer at NO charge

Southwestern Industries
Proto Trak DPM 3 Vertical Bed Mill
with A.G.E. 3 CNC Controls

Demo video of operation

This is a very nice machine with Original Paint
The following Service has just been Completed

All new bearings in variable speed head Including New variable speed belt.
Table removed and cleaned.
All oil gallies have been cleaned, flushed, and verified oiling correctly.
Ball screwed cleaned and flushed with new oil.
New rubber lines replaced to ball screws
Mill has been adjusted and calibrated using Southwestern Industries Calibration Fixture, and is ready for Production

Way covers have been removed for pictures. They will be included with machine.

This is a very nice Mill that runs smooth and quite.
Video of machine operation can be shared upon request.

S/N-97-2899

Table size 50″ X 10 ” ~ with 3 t-slots
Travel X-29 / Y-16″ / Z-24.150″
Maximum weight of work piece: 1,320 LBS
Milling head swivels right & left: 90 Degrees
Quill travel: 5″
Spindle taper: #40 N.S.T
(3) power quill feeds: .002; .004; .006 IPR
Distance, center-line of spindle to face of column: 17.3″
Variable spindle speeds 70-4200 RPM
Full 3-axis CNC machining control or hand wheels for manual operation
Precision and ground ball screws installed in table(X), saddle(Y), and column(Z)
3 H.P. spindle drive motor
Approximate Weight: 4,200 Lbs.
Approximate Dimensions: 71″ x 71″ x 84″ H
Equipped With:
Dual floppy disc drives
RS 232 port
Leveling pads
Remote Stop Go Switch
Coolant Pump
Automatic lubrication system
(cleaned,flushed, and filled with new oil)

Any questions please Call Brandon
Machine is powered and can be tested.

Will load on truck or trailer at no charge.

Hardinge 11” x 18” Precision Toolroom Lathe, Model HLV-H

Demo video of operation

Lathe is in very good condition. and everything moves smooth and free as it should.
Lathe was just serviced Including
Verified that oiler for saddle is working
Spindle bearings have been Cleaned and Repacked with correct Lube.
New Cross Feed Screw and Brass Nut
Cross Slide has been Scraped so fit is near Perfect
New Variable Speed Drive Belts
Electrical contacts have been cleaned.

Lathe will come witha an Aloris Tool Post with Tool Holders
Drill Chuck
Morris Taper Center
And an Assortment of 5C Collets
Work Light
Coolant pump

Specifications:
Swing Over Bed 11”
Swing Over Carriage 9”
Swing Over Cross Slide 6”
Distance between Centers 18”
Hole Thru Spindle 1 ¼”
Compound Slide Travel 3”
Power Feed Range ¼” – 7” per Minute
Spindle Capacity 1 1/4″ with 5C Collets taper
Tailstock Spindle Diameter 1 3/8”
Tailstock Spindle Travel 3 ¾”
Tailstock Spindle Taper No. 2 MT
Leadscrew Diameter 1” – 8 Thread
Range of Threads in Gear Box 11 – 108
Number of Thread Changes in Gear Box 27
Weight 1,700 lbs

Lathe is powered and can be Tested
Any question Please Call Brandon

Southwestern Industries, Inc.
DPM SX2P Bed Mill     2013 model year

with the ProtoTRAK SMX3 Control

Mill has just been serviced and calibrated and is in very good condition.

Mill has brand new power draw bar installed

Mill is powered and can be tested 

Will load on truck or trailer at no charge.

SPECIFICATIONS:

18″ x 40″ Southwestern Industries Proto Trak lathe with LX3 controls

Constant Surface Feed

Traking

5C collet closer

3 jaw chuck

Aloris tool post and holders

Manuals

Southwestern Industries
Proto Trak B3 Sport ( like DPM3) Vertical Bed Mill
with M3 CNC Controls

This is a very nice machine with Original Paint
The following Service has just been Completed

All new bearings in variable speed head Including New variable speed belt.
New sleeve and pulley on Spindle
Table removed and cleaned.
All oil gallies have been cleaned, flushed, and verified oiling correctly.
Ball screwed cleaned and flushed with new oil.
New rubber lines replaced to ball screws

This is a very nice Mill that runs smooth and quite.
Video of machine operation can be shared upon request.

Table size 50″ X 10 ” ~ with 3 t-slots
Travel X-29 / Y-16″ / Z-24.150″
Maximum weight of work piece: 1,320 LBS
Milling head swivels right & left: 90 Degrees
Quill travel: 5″
Spindle taper: #40 N.S.T
(3) power quill feeds: .002; .004; .006 IPR
Distance, center-line of spindle to face of column: 17.3″
Variable spindle speeds 70-4200 RPM
Full 3-axis CNC machining control or hand wheels for manual operation
Precision and ground ball screws installed in table(X), saddle(Y), and column(Z)
3 H.P. spindle drive motor
Approximate Weight: 4,200 Lbs.
Approximate Dimensions: 71″ x 71″ x 84″ H
Equipped With:
Dual floppy disc drives
RS 232 port
Automatic lubrication system
(cleaned,flushed, and filled with new oil)

Kurt power draw bar.
Oiler has been clean ,filled and adjusted.

For SaleRefurbished HEM Saw
Model 1200-A-2
Horizontal Band Saw

Serial Number: 305789

GENERAL SPECIFICATIONS

Capacities

Flats 20″

Rounds 16″

Blade Size 15′ 8″ Long
1.25″ Wide.
.042 Thick

Work Height 29″

Blade Speeds Approx 60-400 FPM

Electric Drive Motor.
7.5 HP
1745 RPM
208-460 volt
3phase

Equipped With:

Hydraulic Feed Control

Adjustable
Cutting Pressure
Clamp Pressure

10′ In Feed Roller Table

25″ Out Feed Table

Adjustable Vise Pressure with 8″ tall jaws

24″ Indexable Infeed Conveyor

8″ High Vise With Hand Lever

Emergency Stop Button

Blade Brush

Chip Auger

Broken Blade Indicator

Out of Stock Indicator

Air Adjustable Blade Tensioner

Wired and Plumbed for Coolant.

While being Refurbished

The saw was disassembled cleaned and painted.

Saw received a
New Gear Box.
New Drive Belt.
All New Saftey and Inscruction Stickers.
New Blade Brush.

Saw is currently setup,with Saw and Infeed Table leveled and can be demonstrated.

Approximate Overall Dimensions Approx. 120″ Left-Right
x
13′ Front-Back
x
53″ Height

Approximate Overall Weight 5000 Lbs

For Sale
Large Heavy Duty 22″x80″Gap Bed Lathe.
Will swing 30+ “s with gap out.
2.900″ Spindle bore
20” 4 jaw chuck
Metric and English threading.
Taper attachment
Steady Rest
Follower Rest.
Quick change tool post and tool holders
#5 Morris taper tailstock
Assortment of carbine indexable cutting tools
Drill Chuck
Live Centers.
Permanent Live center for tailstock
Morris Taper Adapters
Chuck key.
Original Manual including
Parts and electrical diagrams
Maintenance schedule
Lathe has power rapid traverse X and Z axis
15 hp drive motor.
220 volt 3 phase.

Lathe is powered and can be tested.

Any questions please call Brandon

Can load on truck or trailer at no charge.

MM INDUSTRIES VORTI-SIV

Model RBF 15
Serial # 15407
IN EXCELLENT CONDITION.

Used for Sinterstation 3D Printer

INCLUDES A USED STAINLESS STEEL # 80 MESH SCREEN, RISER RING, FUNNEL TOP ,and DISCHARGE HOSE
AS SHOWN IN THE PHOTO’S

1 HP DRIVE MOTOR
SINGLE PHASE 110 OR 220 VOLT

This model is still Manufactured and many different sized sieves or parts are available.
New machine sells for over $9000

Southwestern Industries
Proto Trak DPM 3 Vertical Bed Mill
with A.G.E. 3 CNC Controls

This is a very nice machine with Original Paint
The following Service has just been Completed

All new bearings in variable speed head Including New variable speed belt.
New sleeve and pulley on drive motor.
Table removed and cleaned.
All oil gallies have been cleaned, flushed, and verified oiling correctly.
Ball screwed cleaned and flushed with new oil.
New rubber lines replaced to ball screws

This is a very nice Mill that runs smooth and quite.
Video of machine operation can be shared upon request.

I just had Proto Trak technician , calibrate and adjust machine.
Including a full report of Mill. (see pictures)

S/N-011BF10973
New in 2001
Table size 50″ X 10 ” ~ with 3 t-slots
Travel X-29 / Y-16″ / Z-24.150″
Maximum weight of work piece: 1,320 LBS
Milling head swivels right & left: 90 Degrees
Quill travel: 5″
Spindle taper: #40 N.S.T
(3) power quill feeds: .002; .004; .006 IPR
Distance, center-line of spindle to face of column: 17.3″
Variable spindle speeds 70-4200 RPM
Full 3-axis CNC machining control or hand wheels for manual operation
Precision and ground ball screws installed in table(X), saddle(Y), and column(Z)
5 H.P. spindle drive motor
Approximate Weight: 4,200 Lbs.
Approximate Dimensions: 71″ x 71″ x 84″ H
Equipped With:
Dual floppy disc drives
RS 232 port
NEW Telescoping way covers on Z and Y axis
Leveling pads
Automatic lubrication system
(cleaned,flushed, and filled with new oil)

Torque-Rite power draw bar.
Oiler has been clean ,filled and adjusted.

Any questions please Call Brandon
Machine is powered and can be tested.

Will load on truck or trailer at no charge.

For sale.
Cleveland Mill
9″x42″ Table in good condition.
3 hp drive motor. Currently wired 240 volt 3 phase.
Mill has just been serviced including New bearings and belt in Variable speed Drive
Power quill assembly has been cleaned and adjusted.
Table and saddle removed ,cleaned. All oil gallies have been cleaned flushed and verified that they flow oil properly.
New lead screws and Brass Nuts were installed and adjusted properly.
.005″ – .008″ backlash on X and Y Lead Screw Travel

Mill is powered and can be tested.
Any questions please call Brandon

MAKE WHACHEON ALL Original
MODEL HL- 435 ( serial number 2211780)
SWING 17″ (26″ with gap removed)
CENTERS 40 IN
MOTOR 5HP 220—440 VOLTS 3 PHASE (Switches on control panel have been replaced and function correctly)
SPINDLE D 1-6 spindle with
2.100 spindle bore
10″ 3 jaw chuck (thru-adjust)
4 jaw 12″ chuck
Coolant pump
Quick change tool post.
Micrometer Carriage Stop

SPEEDS (12) 32—-1800
THREADS Inch / metric
Cross slide and lead screw are in perfect condition. (Flaking marks still visible on cross slide see pictures.
Cross slide ,compound, saddle ,and oiling system disassembled ,cleaned and adjusted.
Headstock drained , flushed and filled with New oil.

TAIL STOCK # 4 MORSE TAPER

This is a licensed copy of Mori-Seiki. All parts are interchangeable and available.

Very nice running lathe can be inspected under power

Any questions please call Brandon
Local pickup
Can load on truck or trailer at no charge.

For Sale
Steel Welding Table.
37″ x 72″
1″ thick top
34″ tall
Great Bench that you can pull a chair up to , and get your legs underneath for comfortable and relaxed TIG welding or fabricating.

Can load on truck or trailer at no charge

For sale is a Bridgeport Variable Speed vertical mill.

9″x42″ Table.
2 horsepower
One Shot Lube System.
Chrome ways

New X axis brass nuts
Y axis screws and Brass Nuts.

power quill cleaned and adjusted.
Backlash on feed screws are-.010″ or less and operate smoothly

Mill is currently wired 230 volt 3 phase.

Heavy Duty Weld Table.

48″ x 96″ Table
With 1″ thick Steel top
32″ tall

Base is made out of 2″ x 4″ Rectangular Steel Tube.

Can be loaded on truck or trailer at no ch

For Sale
Welding table
24″x36″
3/4″ thick Steel Top
34″ tall

Well built

Can load on truck or trailer at no charge.

For Sale

2011 Proto Trak K4 Heavy Duty Milling Machine

Machine is in Brand New Condition (Still has all the clear plastic protectors on Factory Labels)

Mill has NOT been painted or had any parts replaced!

Mill Features

Heavy Duty Box ways on Knee and Column

5HP spindle motor with 40 Taper spindle

Late Model SMX Control Updated to the latest software available

This mill has Zero wear and is good as New!

Comes with Coolant  Mister, Halogen work light  and Power Draw bar installed from Factory by  Southwestern Industries

Machine will include factory way covers( removed for inspection and pictures)

Mill will come with Calibration and Certification Records for Proto Trak Technician

Will Load on Truck or Trailer at NO Charge

Hand built Sideshaft Model Hit & Miss Engine.
Engine is built from high grade materials.
Engine features
9″ Flywheels
Cast iron Cylinder Sleeves
And cast iron Rings.
Custom Sideshaft and Governor Assembly
Engine will include coil and battery to operate engine.
Engine starts very easy and runs slow.

Dimensions
18″ long
12″ high
14″ wide
Weight about 100 #s

Please call Terry with any Questions

Hurco (Clausing Kondia) vertical milling machine. Bridgeport style
Model FV-1
Variable speed Drive
R-8 spindle
9″x42″ Table.
Servo 150 Powerfeed
Digital read out. Plus Mitutoyo Z axis Digital Scale
Ways are good condition.

Mill has just been serviced including
New Brass feed Nuts X and Y axis.
All oil gallies cleaned flushed and verified oiling
Gibbs adjusted
3hp 3 phase motor. Currently wired 230 volts.
Mill is powered and can be tested.
Any questions please call Brandon

Can load on truck or trailer at no charge.
Collets ,vise and tooling available at extra cost.

Harrison M300 Toolroom Metal Lathe in like new condition.
13″x40″
1.650″ spindle hole
6″ Bision 3 Jaw chuck
10″ Bergman 4 Jaw Chuck
Quick change Armstrong Tool Post (US Made) and boring bar
Change gears for Metric threading
Taper sleeve and center for headstock
Live and dead center for tailstock
Jacobs drill chuck
OSHA Chuck guard
Chuck adapter
Factory supplied wrenches

Spindle speed 58-2500 rpm
Foot Spindle Brake
Ways on machine are in perfect shape. (See Pictures)
Lathe has been serviced and ready for production.

Any Questions Please call Brandon
Will load on truck or Trailer at No charge

Stone Cold Saw
Model M120
24″ Carbide tipped Blade in Good Condition
8 1/2″ capacity
10 horsepower
Adjustable feed stop
Feed Table
Air Powered Vise
Extended Handle

Currently wired 220 volt # phase

Any question Please call Brandon

Will load on truck or trailer at No charge

Kalamazoo Model FS-350SA
Saw is easy to operate
With a push of button ,
1 Vise will close
2 blade starts
3 Adjustable speed down will cut part off
4 Blade will retract
5 Blade will shut off
6 Vise will open

Video of saw in operation
www.youtube.com/watch?v=Ow97lzCI6nA

Saw can cut precision miter or straight cuts.
Includes coolant system (just cleaned)
5 blades with different pitch teeth for different project needs

3hp 2 speed motor wired 220 volt 3 Phase

Cold Saw is powered and can be tested

Any questions Please call Brandon
Will load on truck or trailer at No Charge

2011 Southwestern Industries 1845 SX
Proto Trak CNC Lathe with SLX controler.

Lathe is outfitted Late model SLX controller with advanced features and Traking option
STAR Programmable Tool Changer
Also includes standard tool post mount
Roller bearing Steady Rest
2.400″ spindle bore with D1-6 cam lock chuck
10″ 3 jaw Bison Chuck
10″ 4 jaw
# 4 MT Jacobs drill chuck
Start- Stop Remote Control
Programs Manuals

Available at extra cost.
12″ 6 jaw Pratt Burnerd with Adjustable Scroll D1-6
Jacobs Rubber Flex Collet Closer D1-6

Lathe has just been serviced , including
Drain , Flush and Fill Head stock oil
Saddle ,Cross slide, and ball Screws, removed, cleaned, inspected, and adjusted
All oil gallies have been cleaned , flushed ,and verified oiling correctly

Lathe will be Calibrated and certified by Proto trak and will come with Paperwork.

Lathe is powered and can be tested!
Any Questions Please Call Brandon

Will load on truck or trailer at NO charge

Webb Vertical Mill 10″x50″ Table
with AGE Prototrak 2 axis cnc control.
3hp spindle.
Mill has just been inspected and Serviced
Including
New variable speed belt ,bearings and head inspected
Table removed and cleaned.
Verified oiling system is working correctly.
Reassembled and Gibbs adjusted.
Mill has be calibrated by proto trak technician and will come with paperwork stating machine tolerance and repeatability.

Mill is powered and can be tested.
Any questions please call Brandon
Can load on truck or trailer at NO charge.

Hone includes “Light Cutting Pressure Control” for precision work
work light
Mandrels that come with hone , range from 3/16″ – 1″ quantity of 23

Larger Mandrels are available at additional cost

220 volt 3 phase I can supply converter at no charge.

Hone is Powered and can be tested

Any questions Please Call Brandon

Will load on truck or trailer at no charge!

Nikuni High Pressure Coolant pump with Filtration and Lift Pump

This High Pressure coolant Pump System Includes everything in 1 convenient unit on wheels

High pressure pump is powered by a
3.7 kw (5hp)
3 phase electric motor ( 220 volts)
that drives the
Nikuni positive displacement pumps feature a seal-less pumping chamber so there are no seals, packing or cups to leak or replace. The seal-less design and check valves enable Nikuni to handle abrasives and particulates that would damage other types of pumps.

Coolant tank
Lift pump (suction pump) also 3 phase power.
Larger Filtration filtering system.

This pump was purchased by a larger manufacture and was only used for 6 weeks

Saw capacity: 16″ square, 16″round, 20″ flat
Blade size: 11/4: X 15’8″X.042 thk, shut off switch if blade breaks.
Brush: powered brush assembly-brush size 1/2″ X 40.
Electricals: 7.5 HP drive motor, 220/440 vac, 30, 1800 RPM, ball bearing TFC, 1/6 HP sealed submersible coolant pump.
Drive mechanism is totally enclosed, running in oil, gear reducer with variable speed drive 60-400 (FPM).
Semi-automatic saw operation: When material is placed in vise and cycle is initiated; motor will turn on, vise will clamp and arm will cut through material. When material is cut: motor will turn off and saw arm raises and clamp opens. Transformer to provide low voltage for 24 volt logic solid state circuit. hydro-pneumatic power saw arm lift to give controlled feed rates and adjustable clamping pressures. Pneumatic controlled vise to clamp material. Adjustable clamping pressure.
Optional equipment: 10′ X 20″ Roller load table (attaches to saw).

Optional 9″x48″ Table.
2 horsepower
One Shot Lube System.
Chrome ways Good condition
Sony Digital Read Out

I just finished servicing mill including following work.
Mill has been disassembled ,all oil galleies have been cleaned.
Then was reassembled and adjusted.
New variable speed belt
New bearings in Variable speed.
All drive pulleys have new bushing installed
Power quill adjusted.
Backlash on feed screws are-.010″ and operate smoothly
Mill is currently wired 230 volt 3 phase.

9″x42″ Table.
1 1/2 horsepower
One Shot Lube System.
Chrome ways in good condition
Acurite DRO.

New X and Y screws and Brass Nuts.

power quill adjusted.
Backlash on feed screws are-.010″ or lead and operate smoothly

Mill is currently wired 230 volt 3 phase.

Falls D-Bur-r model 111
This machine will debur sheet metal from 24 gauge- 1/4″
Comes with extra cutters.
It’s is powered by 110 volt single phase.
Also have model 121 included for parts.

Economy brand ,Die Cart ,Lift table.
Mini Forklift
1500# capacity Hydraulic lift.
Lifts 60″s high.
New 12 volt Deep Cycle Battery.
On board battery charger.
Works good. $475

Jamestown 10 gauge Power slip roller 38″
4″ diameter Rolls.
Power roller with Single phase 220volt motor.
Machine is under power and can be tested.

Peck Willcox and Stow
Pexto
Niagara
Diarco

Hand built Sideshaft Model Hit & Miss Engine.
Engine is built from high grade materials.
Engine features
10″ Flywheels
Cast iron Cylinder Sleeves
And cast iron Rings.
Custom Sideshaft and Governor Assembly
Engine will include coil and battery to operate engine.
Engine starts very easy and runs slow.

Dimensions
18″ long
12″ high
14″ wide
Weight about 100 #s

Greenerd #3 Arbor Press
3 ton
On Factory built cast stand.
Press is in very good condition.

Famco Model 5c Arbor Press.
12 ton
Adjustable knee
Ratchet drive.
Press has been disassembled cleaned and painted. Oiled and reassembled.
Press is in good condition
No broken castings

US made.
Thor Tool and Die Company.
Model 2018
18 position
1 lever unlocks both top and bottom platter for indexing. .
Platters are coupled with chain and sprockets.
Works very Smooth and Efficiently

Small hole is 1/8″ – large hole is 2″

17 ton. Hand operated Punch

48″ wide table Layout table.
With 1″ grid scribed vertical and horizontal ,to use with adjustable fence

Comes on factory stand.

2013 Manufactured

VERY LOW HOURS.

24.5″ x 74″ 620mm X 2 meters

Siemens CNC CONTROL

ASA A2-8 Spindle nose

Direct Drive Spindle

104mm (4.09″) thru the spindle hole

1 to 1800 rpm

SAUTER 8 position Tool Changer. Made in Germany

3 Boring bar holders for ID Work

Threading tool

Turning tool

Boring bar.

16″ Bison 3 jaw chuck

16″ 4 jaw Bison Chuck (NEW)

Romi Manuals and Software backup

Royal Morse taper #5 Live Center.

Coolant tank and pump
Coolant plumbed through the tool Changer.

Lathe has a onboard transformer that can be used to wire lathe 208-480 volts 3 phase.

Lathe has just been inspected and Serviced by
Romi and Given a A+ report.
(Can supply report if interested)

Lathe is under power and can be tested.
This is a like New machine with very little use.

For sale
Greenerd #4 Arbor Press
7 ton
Ratchet
Adjustable Knee
Press has been disassembled ,cleaned, and painted.
Oiled and reassembled.
No broken castings
I have several other arbor presses
Any questions please call Brandon
Will load on truck or trailer at NO charge

Clausing Kondia vertical milling machine. Bridgeport style
Model FV-1
Variable speed Drive
R-8 spindle
9″x48″ Table.
Servo 150 Powerfeed
Newell digital read out.
Ways are very good condition.

Mill has just been serviced including
New bearings and belt in Variable speed.
All oil gallies cleaned flushed and verified oiling
Gibbs adjusted
3hp 3 phase motor. Currently wired 230 volts.
Mill is powered and can be tested.